The wheels spacer bolts onto the vehicle on the existing studs with the nuts supplied. Your wheel then bolts onto the wheel spacer using the studs on the wheel spacer and your original nuts.
NOTE: If you use it on steel rims the studs are too long for the chrome nuts and you have to trim the studs a little bit. It is however no problem with mags.
Make sure the surface on the vehicle hub is clean and free from any debris before fitment. The same applies to the back of the wheel spacer which should be clean. Tighten all nuts by hand first, then torque in cross over sequence to 30 Nm. Then Torque to 100Nm. When you have them fitted at a tyre fitment centre, keep an eye on the procedures because they normally tighten it with impact wrench. DO NOT allow them to use an impact wrench and make sure they tighten them in cross over sequence. Check the wheel spacer nuts after the first 500 km to make sure they are tight. Thereafter check every 5000km.
* The use of thread locker will void the warranty of these wheel spacers Reason: How do you frequently check the torque if you used thread locker?
The picture below shows how to fit the wheel spacer to your vehicle
Fits all Ford Ranger and Ford Courier models
PCD = 139.7 Inner Bore = 93.1mm Thickness = 30mm Stud = M12x1.5
NOTE: If your vehicle has a manual hub in front the spigot ring will not go over it.Max Torque DRY = 120Nm Max Torque oiled / greased = 110 Nm .
Price per spacer
6/139.7 Wheel spacer fits front and rear on auto hub models like Revo, Vigo, Prado and FJ Cruiser. Also fits the 2026 FJ Cruiser
NOTE: Because of the spigot ring it will NOT fit over a manual hub like on the SFA, IFS Hilux, 80 series Cruiser and some 100 series Cruisers.
On SFA and IFS Hiluxes and the older Cruisers it will only fit at the rear and...
This extra stud fits the 6 stud wheel spacer used for Hilux, Ford, Mazda, Mitsibushi and others.
Stud - M12x1.5mm - high tensile 12.9 grade
Nuts - 40CrMo high tensile steel
Wheel nut with Shank for Toyota Land Hilux with Aluminium rims. M12x1.5
These wheel nuts are used when you fit the standard OEM aluminium rims on a Hilux.
Length 47mm -
Wheel nut with Shank for Toyota Land Cruiser with Aluminium rims. M14x1.5
These wheel nuts are used when you fit the standard OEM aluminium rims on a Land Cruiser.
Length 47mm
OD of Shank is 18mm. Please note there is models that use 22mm Shank.
Please measure your OD before ordering
Wheel Spacer for Jimny, SJ40, Lada Niva, Ford F100.
5 Stud Spacer with 139.7 mm PCD. 30mm thick. Max Torque DRY = 120Nm Max Torque oiled / greased = 110 Nm .
Price is per one spacer
5 Stud Wheel Spacer for Land Rover Defender and Disco One.
38mm thick, 165.1 mm PCD. Max Torque DRY = 150Nm, Max Torque oiled / greased = 120 Nm
Price per one spacer.
These extra studs will fit the 5 stud Land Cruiser wheel spacer - M14 x 1.5
Stud - M14x1.5mm - high tensile 12.9 grade
Nuts - 40CrMo high tensile steel
Jeep Wrangler JK 2007-2018
5 Stud Wheel spacer with 127mm PCD
30mm thick, with spigot ring Max Torque DRY = 120Nm Max Torque oiled / greased = 110 Nm .
Price per one. NOTE: They do not fit the 2025 Cherokee as the Cherokee has thicker studs.
These wheel spacers will only fit up to 2018 Jimny models.
5x139.7, M12x1.25 , Centre bore 108.1mm .
Max Torque DRY = 120Nm Max Torque oiled / greased = 110 Nm .
Please note:It does not fit on Hilux Revo Models (2016-onwards), the Revo's standard studs are too short
6 Stud Wheel Spacer for Hilux, Triton, Ford, Isuzu. 6 stud
PCD139.7mm and centre bore is 108mm 30mm thick
Max Torque DRY = 120Nm Max Torque oiled / greased = 110 Nm
